There’s a company I use through work and they don’t list M10 with a 2 pitch, you need to move to M14 & M16 to get a 2 pitch
There’s a company I use through work and they don’t list M10 with a 2 pitch, you need to move to M14 & M16 to get a 2 pitch
I have a TYG000250 in front of me. It's M10 x 1.5 x 50mm with a threaded portion of 40mm and a full diameter of 7mm. The flanged bolt head suits an E12 socket.
Unfortunately a DIN 912 socket head capscrew M10 x 50 12.9 has a threaded portion of 32mm. You can buy these quite readily. You'd have to get an M10 x 1.5 (standard M10 pitch) die to extend the thread if you wanted to replicate the original.
Regards
Andrew
Can you post a photo Andrew? Could possibly get a longer bolt and cut down to length?
Or
Finish Self Colour Fully Threaded Yes General Tolerances +/- 0.13mm Head Diameter (D) 16mm Head Length (H) 10mm Hexagon A/F (J) 8mm Hexagon Depth (P) 5mm Length (L) 50mm Manufacturing Standard DIN 912 Material 12.9 Hardened Steel Material Specification 12.9 Hardened Steel Screw Thread Pitch 1.5mm Thread Length (Max) 50mm Thread Size (T) M10 (10mm)
Bolt (2).png Bolt (1).png
Nich.
...
Last edited by Nich; 08-06-2018 at 08:58 PM.
Nicholas John Peter Tinker - # 484
Manufactured on Tuesday 27th April 2004 @ 12.17.47.
Commission Number: 24468.
Brochure Model: M3 Tourer 4.6 V8 260PS.
Specification Code: L01B.
CICode: D1511.
Trim Level: TL8.9 (M3).
65th ZT-T 260SE to be made out of 115.
11th ZT-T 260 SE in Pearl Black (PBT) out of 23 produced.
Manufactured in the UK by MG Rover Group Ltd.
Is a fully threaded version not available?
Steve
Too late Steve, fully threaded available.
Nich.
...
Nicholas John Peter Tinker - # 484
Manufactured on Tuesday 27th April 2004 @ 12.17.47.
Commission Number: 24468.
Brochure Model: M3 Tourer 4.6 V8 260PS.
Specification Code: L01B.
CICode: D1511.
Trim Level: TL8.9 (M3).
65th ZT-T 260SE to be made out of 115.
11th ZT-T 260 SE in Pearl Black (PBT) out of 23 produced.
Manufactured in the UK by MG Rover Group Ltd.
AAAhh so! Another bit of wrong information to send me down a path with no hope. I didn't dare take out another bolt from my car to check the spec and so relied on the forum which had a post in another thread stating it was pitch 2. Most bolts in the automotive trade are 1.5 for drive-line (BMW, JLR, Vauxhall). I will now search for a 1.5 x 50mm.
Thanks for that Andrew, the information is more reassuring.
Kev
Could try here Kev..........as I said earlier!
https://www.accu.co.uk/en/cap-head-s...CF-M10-50-12-9
Nich.
...
Nicholas John Peter Tinker - # 484
Manufactured on Tuesday 27th April 2004 @ 12.17.47.
Commission Number: 24468.
Brochure Model: M3 Tourer 4.6 V8 260PS.
Specification Code: L01B.
CICode: D1511.
Trim Level: TL8.9 (M3).
65th ZT-T 260SE to be made out of 115.
11th ZT-T 260 SE in Pearl Black (PBT) out of 23 produced.
Manufactured in the UK by MG Rover Group Ltd.
Pictures are here: https://www.two-sixties.co.uk/mgoc260/html/photopost/showphoto.php?photo=11285&title=zyg0000250&cat=502
The bolt is per my earlier post in this thread.
I found the application of heat to be the best way of removing these bolts. The thread-locking material makes them very tight to undo otherwise. The difference heat makes is unbelievable. May I suggest that if you use heat to get the bolts out, they should be perfectly capable of being re-used with a suitable threadlocking compound applied, such as Loctite 270.
Andrew
A bit more mystery info Andrew. Vehicle in at Austin's for 60k service and EML.
Nick reckons that MGR may have been about to update part numbers when they went bust. TYG000260 is probably the same bolt. However, TYG000260 is 1.25 pitch.
One wouldn't have thought that a simple bolt would cause such grief!
Kev
p.s.
Is the Febig box pic relative
Last edited by torque2me; 29-06-2018 at 11:24 AM. Reason: data correction
Kev,
I don't understand "Is the Febig box pic relative".
As for TYG000260, this bolt is completely different from TYG000250.
TYG000250: M10 x 1.5 x 50mm with a threaded portion of 40mm and a full shank diameter over a length of 7mm. The flanged bolt head suits an E12 socket.
TYG000260: M10 x 1.25 x 60mm with a threaded portion of 28mm and a full shank diameter over a length of 30mm. The flanged bolt head suits an E12 socket.
They aren't the "same bolt" at all.
Andrew