That's the one. Daryl Cramer is the name I was told, apparently he worked at Rover dealer. Is he well known? Or have you used him?
That's the one. Daryl Cramer is the name I was told, apparently he worked at Rover dealer. Is he well known? Or have you used him?
They have recently become known in mgf circles
Beware though, working at a dealer does not automatically make them good for our cars
Personally I would rather travel and use someone with a good reputation for our cars
AE Wilcox near Bristol
Nick and Jean at Austin Garages in the midlands
Dreadnought up in Scotland
Etc etc
colintf
Colin Murrell
vin 00242 - Probably the only 260 to have driven the full Le Mans circuit?
MG Car Club Z Register V8 ZT/ZTT Rep.
MG Car Club V8 Register V8 ZT/ZTT Rep
MG Car Club MGF Register Regional Rep for Devon & Cornwall and Cotswold Regions.
MG Car Club MGF Register International Liaison Representative
http://www.mgfim.org/
http://www.two-sixties.com/main.htm
http://www.v8register.net/
http://www.mgfregister.org/
http://www.racethemg.com/ http://www.triple-mracing.com/
Member of MGCC (UK), MGOC, VSCC & TSSC (Triumph Sports Six Club)
I'd agree with that. Although there's none close to home unfortunaly. I think the nearest one is something like a 3 hour drive for me, hence why I'm trying to find a local place with at least some experience. For planned jobs travelling wouldn't be a problem.
Who does the likes of Tim or Ajay etc use????
colintf
Colin Murrell
vin 00242 - Probably the only 260 to have driven the full Le Mans circuit?
MG Car Club Z Register V8 ZT/ZTT Rep.
MG Car Club V8 Register V8 ZT/ZTT Rep
MG Car Club MGF Register Regional Rep for Devon & Cornwall and Cotswold Regions.
MG Car Club MGF Register International Liaison Representative
http://www.mgfim.org/
http://www.two-sixties.com/main.htm
http://www.v8register.net/
http://www.mgfregister.org/
http://www.racethemg.com/ http://www.triple-mracing.com/
Member of MGCC (UK), MGOC, VSCC & TSSC (Triumph Sports Six Club)
In the end it's just shot-blasting some welded tubes and coat them. Any proper workshop should be able to do that.
Our cars are not different from other cars. 4 wheels, subframes, doors and engine.
We have to be carefull not to create our own niche market where people think they can up the price because a 260 owner needs work done.
(not linked to the above mentioned ones of course)
Last edited by Herman; 05-04-2013 at 02:56 PM.
Fear keeps you alive. Fearless gets you killed
Herman
Vin#076 pics, Black, modified and with 234 RWHP and 276 lb/ft (275 BHP and 440 Nm @ flywheel)
FJ1200, DynoJet Stage 1, K&N filter
Alfa MiTo 1.4 Cloverleaf, 170 BHP, Alfa Rosso.
colintf
Colin Murrell
vin 00242 - Probably the only 260 to have driven the full Le Mans circuit?
MG Car Club Z Register V8 ZT/ZTT Rep.
MG Car Club V8 Register V8 ZT/ZTT Rep
MG Car Club MGF Register Regional Rep for Devon & Cornwall and Cotswold Regions.
MG Car Club MGF Register International Liaison Representative
http://www.mgfim.org/
http://www.two-sixties.com/main.htm
http://www.v8register.net/
http://www.mgfregister.org/
http://www.racethemg.com/ http://www.triple-mracing.com/
Member of MGCC (UK), MGOC, VSCC & TSSC (Triumph Sports Six Club)
I was thinking general mechanics too. Good point though Herman. The local owners I've spoken to (not just 260 owners but other variants of the 75/ZT) have difficulties finding a trusty local garage with a T4 setup let alone experience with the 260
As for the power coating, already picked it up They had it all done in about 4 hours. Incredible service. Just need to treat the inside with some waxoyl.
To be fair Colin, things like taking a gearbox out is more common sense than difficult. You have to get enough clearance to take it out without putting sideload on the input shaft to avoid bending it.
It's the same for every gearbox. In our case it means dropping the sub frame. It's people that take shortcuts that do the damage. (kwik fit with airgun on wheel bolts for example)
So again any decent workshop should be able to do that.
It may be a special car due due it's limited numbers but mechanically it's still a car
Fear keeps you alive. Fearless gets you killed
Herman
Vin#076 pics, Black, modified and with 234 RWHP and 276 lb/ft (275 BHP and 440 Nm @ flywheel)
FJ1200, DynoJet Stage 1, K&N filter
Alfa MiTo 1.4 Cloverleaf, 170 BHP, Alfa Rosso.
Just used that waxoyl stuff. Totally different to how I thought it would be, much easier too. So here's a few pics of the frame ready for fitting. I think it looks pretty good. Now I've treated the inside of the frame, is it worth sealing the holes?
Looks good.........
With regards to plugging the holes................wouldn't know but expect you need some holes to allow condensation to evaporate.....
Someone will know
Fear keeps you alive. Fearless gets you killed
Herman
Vin#076 pics, Black, modified and with 234 RWHP and 276 lb/ft (275 BHP and 440 Nm @ flywheel)
FJ1200, DynoJet Stage 1, K&N filter
Alfa MiTo 1.4 Cloverleaf, 170 BHP, Alfa Rosso.