Fear keeps you alive. Fearless gets you killed
Herman
Vin#076 pics, Black, modified and with 234 RWHP and 276 lb/ft (275 BHP and 440 Nm @ flywheel)
FJ1200, DynoJet Stage 1, K&N filter
Alfa MiTo 1.4 Cloverleaf, 170 BHP, Alfa Rosso.
The lights on her 180 ZT-T (now sold to my daughter, Amelia) were really bad after 160,000kms in the Aussie sun. They were becoming quite opaque and discoloured. Her partner Ross bought a similar kit and spent a similar number of hours to bring them back to clarity (see photos). Not sure how long they will last though - that sun is pretty intense! It would be nice if the covers could be bought separately from the whole light fitting. I assume they just clip off, but most threads on this issue indicate that you have to buy the complete lights to get new covers. This might need to be a future product for the shop.
Last edited by Malcolmr; 28-05-2012 at 01:18 AM.
VIN 206
This is definitely not her car...
I spoke to Hella about new covers and they said they couldn't help because although they made the original units all of the original moulds had ended up with MGR. Anyone know where they are likely to be now?
Nich.
Nicholas John Peter Tinker - # 484
Manufactured on Tuesday 27th April 2004 @ 12.17.47.
Commission Number: 24468.
Brochure Model: M3 Tourer 4.6 V8 260PS.
Specification Code: L01B.
CICode: D1511.
Trim Level: TL8.9 (M3).
65th ZT-T 260SE to be made out of 115.
11th ZT-T 260 SE in Pearl Black (PBT) out of 23 produced.
Manufactured in the UK by MG Rover Group Ltd.
Fear keeps you alive. Fearless gets you killed
Herman
Vin#076 pics, Black, modified and with 234 RWHP and 276 lb/ft (275 BHP and 440 Nm @ flywheel)
FJ1200, DynoJet Stage 1, K&N filter
Alfa MiTo 1.4 Cloverleaf, 170 BHP, Alfa Rosso.
Looks good, but how did it deal with stone chips on the headlamps?
I have wondered as this kind of damage isnt just surface deep quite often...
I didn't have any nasty chips, but the surface was quite rough and dirt was caught clouding the lenses.
The process is a bit like T-cutting, polishing out the roughness. I would hope that with the surface smoothed out it will help keep the lenses clear long term, but a bit like claying and polishing paintwork, it will probably be best to do it on a regular basis.
I would say that a day later after the polish has dried out, there is still more work to be done, but it is without a doubt better than it was.
Looks good!
Klaus
Klaus
Northern Germany
2021 Mercedes-Benz GLC 300e X254 -company car-
2005 MG ZT 260 RX #315 Beast! -summer days-
1972 Mercedes-Benz 280S W108 -very few summer days-
1991 Mercedes-Benz 300TE-24 S124 -under complete restoration-
Colin Ellis #456 It'll be alright in the end. If it's not alright, it's not the end
Just a little up in the acrilic polishing.
I found a very rare item, an old "mobile" phone from a Range Rover Classic, from around 1988/9.
It was a mess!
Telemovel Range Rover - 2013-01-28 002.jpg
And I even did worst when I was cleaning with Alcohol!
Telemovel Range Rover - 2013-01-31 001.jpg
After a search on the web, I found that with cheap products, we can have the same reults with much lesser waiste of money.
Firts step.
Telemovel Range Rover - 2013-02-02 018.jpg Telemovel Range Rover - 2013-02-02 019.jpg
Just rub the acrilic face with wet sand paper (1000 grade), gently!
After that the acrilic face seems a little milky! Don't worry!
Telemovel Range Rover - 2013-02-02 020.jpg
Next step, polish with Duraglit with a soft cloth.
Telemovel Range Rover - 2013-02-02 021.jpg Telemovel Range Rover - 2013-02-02 022.jpg
And the result:
Telemovel Range Rover - 2013-02-02 037.jpg Telemovel Range Rover - 2013-02-02 042.jpg Telemovel Range Rover - 2013-02-02 039.jpg Telemovel Range Rover - 2013-02-02 040.jpg Telemovel Range Rover - 2013-02-02 041.jpg
HeadlampLensClean270614 002.jpg HeadlampLensClean270614 003.jpg
... then after using Meguiar's 4 small sanding pads, not a little elbow grease, then their cream and drill bit attachment tickling stick, after an hour ...
HeadlampLensClean270614 007.jpgHeadlampLensClean270614 009.jpg
.... then the rain came so i will have another bash tomorrow