Any one want a cheap 75mm throttle body
Results 1 to 8 of 8

Thread: Any one want a cheap 75mm throttle body

  1. #1
    Registered User SCP440's Avatar
    Join Date
    Jan 2016
    Location
    Witney Oxfordshire
    Posts
    2,353

    Default Any one want a cheap 75mm throttle body

    https://www.ebay.co.uk/itm/304884918159
    Nothing to do with me but seems like a bargain for someone.
    Last edited by David; 11-04-2023 at 01:58 PM.

  2. #2
    #829 called 'Olive' David's Avatar
    Join Date
    Jun 2015
    Location
    Breugel, Holland
    Posts
    6,150

    Default

    Quote Originally Posted by SCP440 View Post
    https://www.ebay.co.uk/itm/304884918159
    Nothing to do with me but seems like a bargain for someone.
    The advertiser is a member here, I see ('Spinakerr'), but didn't think about putting it in the "Items for Sale" thread here for some reason.
    Those bodies are still available on the 'Bay but at a tad over 40 quid , and I don't think you really need the extra screws etc. which they send you new from China. May be wrong. https://www.ebay.co.uk/itm/300829363968

    David
    Last edited by David; 11-04-2023 at 02:31 PM.

  3. #3
    Registered User Dashnine's Avatar
    Join Date
    Feb 2022
    Location
    Studley
    Posts
    154

    Default

    It was the lack of extra bits in comparison to the similar eBay items that put me off, not knowing if they were needed or not.
    Life's too short to drive boring cars!

    MG ZT 260 #442 in XPower Grey

  4. #4
    #829 called 'Olive' David's Avatar
    Join Date
    Jun 2015
    Location
    Breugel, Holland
    Posts
    6,150

    Default

    Quote Originally Posted by Dashnine View Post
    It was the lack of extra bits in comparison to the similar eBay items that put me off, not knowing if they were needed or not.
    You only know for 100% when you have it in your hand, but the one from the club a few of years back, came with nothing extra, no screws etc., and fitted "plug 'n play". Just reused the existing fitting nuts and re-used the paper gasket, if that's any guide. Only problems were the TPS screws (gave up, and bought a new TPS, fitted using socket-cap M5x30 bolts), and tempting the 'rubber' trunking to grow to 75mm!

    A very worthwhile improvement I found, together with the EGR plate, and even then at over £100, a cheap, effective power-per-pound choice.

    David
    Last edited by David; 11-04-2023 at 04:43 PM.

  5. #5
    Registered User Dashnine's Avatar
    Join Date
    Feb 2022
    Location
    Studley
    Posts
    154

    Default

    So to the follow on, is there more power to be gained from the extra air without a remap, does the ECU detect more air going in and add more fuel? Is there a noticeable benefit (with or without a rolling road)?

    I suppose the answer to both is yes, otherwise why bother?. :-)
    Life's too short to drive boring cars!

    MG ZT 260 #442 in XPower Grey

  6. #6
    #829 called 'Olive' David's Avatar
    Join Date
    Jun 2015
    Location
    Breugel, Holland
    Posts
    6,150

    Default

    Quote Originally Posted by Dashnine View Post
    So to the follow on, is there more power to be gained from the extra air without a remap, does the ECU detect more air going in and add more fuel? Is there a noticeable benefit (with or without a rolling road)?

    I suppose the answer to both is yes, otherwise why bother?. :-)
    No proof of extra hp, but certainly FEELS like it has. Also feels much smoother running, better pick-up and eager in acceleration, particularly 500-2500 range. Ever so slightly better consumption figures (?). No down side?

    That is extra important on an auto like mine of course, since it influences the shift point logic of the ECU in a positive way, but most ZT260 owners are satisfied too, I believe.

    Like I say, low cost, no re-map, P&P DIY job. Just don't expect it to feel like a Dreadnought or Roush equipped car as a result!

    David
    Last edited by David; 11-04-2023 at 05:03 PM.

  7. #7
    Registered User SCP440's Avatar
    Join Date
    Jan 2016
    Location
    Witney Oxfordshire
    Posts
    2,353

    Default

    Yes worth fitting, no down sides. As David has said the rubber hose needs some help to get it to fit over the bigger inlet. I used a hot air gun to warm it up. The existing jubille clip will still work.

    The biggest difference I noticed was the mid range pick up and it seems to run out of breath higher up the rev range.

    Nothing to worry about with the emissions, mine always fly's through the annual MOT.

  8. #8
    Registered User
    Join Date
    Jan 2021
    Location
    West London
    Posts
    30

    Default

    Hi all -sorry I should have posted here first - just having a clear out of a lot of items for all the cars in the garages!

    Will put items here in future.

    Went to a member here I believe.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •